How to Clean Saw Blades
How to Clean Saw Blades

HOW TO CLEAN SAW BLADES


What You Need

  • Simple Green Pro HD Heavy-Duty Cleaner
  • Aluminum pan or shallow container
  • Old toothbrush, small brass brush, hard bristle brush, or steel wool
  • Paper towels
  • Blow dryer or can or compressed air (optional)
  • Silicone spray (optional)

A saw may be one of the most resilient - and most dangerous - tools in your workshop. But after project on top of project, your circular, miter, band, hand, or table saw blades can become caked and clogged with pitch, glue, and other materials.


This clogging buildup may make it seem as if your blades are dull, but more often than not, they are just in need of a good deep cleaning. Grimy blades can make it more difficult for you to cut edges cleanly, increasing friction and generating higher levels of heat. This accelerates the dulling process and can cause the blades to warp or distort while you're using them.


Caustic oven cleaners are sometimes recommended as the best way to clean table saw blades. Sodium hydroxide, also known as lye, is the main ingredient in many spray-on oven cleaners. This can cause severe respiratory irritation, nausea, dizziness, skin burns, and more. Other varieties of commercial blade and bit cleaners often don't stay wet for the prescribed amount of soaking time, which doesn't do much to loosen residue from the blade.


In addition to being toxic, oven cleaner and saw blade cleaning products with caustic ingredients can potentially damage saw blades. They attack the binder in the carbide and the brazing used to secure the teeth to the blade.


Simple Green Pro HD Heavy-Duty Cleaner is a readily biodegradable*, non-corrosive, professional-grade cleaner and degreaser ideal for use on tools, equipment, and vehicles. It quickly eliminates tough grease and grime, removes oily stains, and is safe on metal surfaces. The concentrated formula can be diluted to suit your cleaning needs, whether you're cleaning hand saw blades or wiping down your work area.


Check your saw blades often and keep them clean. It is recommended that you deep clean them two or three times a year.


Directions for Cleaning Saw Blades:

Before you begin cleaning, it's a good idea to put a pair of gloves on to protect your hands from the saw's sharp blades.

  1. Prepare your Simple Green solution. Mix 1 cup of Simple Green Pro HD with 3 cups of water in an aluminum pan or a wide, shallow plastic bowl or container.
  2. Remove the blade. Unplug your saw and remove the dirty blade, being careful of the sharp teeth.
  3. Soak the blade. Lay the blade flat in your pan or container, so it is completely submerged in the cleaning solution. Leave it to soak for about 10 minutes.
  4. Clean. After 10 minutes, scrub the blade's teeth and any gunky areas with an old toothbrush, small brass brush, hard bristle brush, or steel wool.
  5. Rinse. Rinse with clean water and pat dry with paper towels. It's important to thoroughly dry the blade, as leftover water could lead to rust. You may even want to use a blow dryer or air compressor to ensure the areas around the teeth and in the gullets are completely dry.
  6. Replace the blade.

TIP: After the blades are clean, give them a coat of silicone spray. This will help slow down the buildup of tars, resins, and rust on the carbide teeth. Silicone may interfere with your workpieces and cause finishing issues. Use your best judgement on when silicone should be applied.


TIP: If a lot of teeth are damaged or getting dull, consider sharpening or buying a new saw. While plain steel saw blades can be sharpened with a triangular metal file, blades with carbide-tipped teeth must be professionally sharpened.


TIP: Some websites recommend soaking blades overnight. While this won’t harm the carbide edges, it can cause the paint to bubble or peel.

Sign Up For Our Newsletter

WHERE TO BUY

Home Depot
Amazon
Walmart
Ace Hardware
Sherwin Williams
Fred Meyer
Camping World
Sign Up For Our Newsletter

Join Our Mailing List